|
Single Gauges $440, Dual Gauges $680, Triple Gauges $920 (Prices include GST and delivery)
Current Supported Vehicles: Commodore VU - VZ 5.7L V8, VZ - VE 6.0L V8 The Interceptor is capable of displaying the following parameters, two at a time, at a
rate of approximately 20 times per second. Not all are supported by every vehicle, so
there is no guarantee that the Interceptor will display all of these on your particular car
or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this
and make it available for display.
 | | RPM
| | | Kilometers Per Hour (KPH)
| | | Intake Air Temperature
| | | Mass Air Flow Sensor Frequency
| | | Mass Air Flow Sensor (lb/min.)
| | | Engine Coolant Temperature
| | | Injector Pulse Width (bank 1 and 2 if supported)
| | | Long Term Fuel Trim (bank 1 and 2 if supported)
| | | Short Term Fuel Trim (bank 1 and 2 if supported)
| | | O2 Sensor Voltage (bank 1 and 2 if supported)
| | | Manifold Pressure in PSI (Boost pressure for factory turbo/supercharger applications)
| | | Ignition Advance
| | | Knock Retard
| | | Engine Run Time
| | | Battery Voltage
| | | Transmission Temperature
| | | Idle air Control Counts
| | | Throttle Position Percentage
| | | Throttle Position Voltage
| | | Engine Load
| | | Oil pressure (some 8 cylinder engines)
| | | Fuel economy (vehicle must have a MAF
| | | Horsepower sensor for these 2 items)
| | | Two user configurable analog inputs |
The Interceptor gauge is 52mm (2 1/16") in diameter and will fit in all standard gauge
pods of this size. A 5' cable is included with appropriate OBD2 connector. A splitter cable
is included with the dual Interceptor units.
A function menu is available by pushing both buttons simultaneously. The first option
allows you to enter a record mode. Once selected, the Interceptor will return to normal
scan mode, but will start recording the displayed data automatically when the throttle
exceeds 60%. Approximately 45-60 seconds of data will be stored. Returning to the menu
screen, you can choose to replay the stored data on the Interceptor display.
Another menu option offers the ability to swap the foreground and backround colors of the
display, this can be seen in the Gallery section. Using this feature, for
example, the gauge with a black backround and blue characters (negative image)
becomes a blue backround with black characters (positive image). Not only can this be
visually appealing but beneficial in changing lighting conditions. Positive images are
easier to read in bright sunlight, negative at night.
The Interceptor's scan rate can also be adjusted through a menu function.
DTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options. Click
here for a list of powertrain diagnostic code explainations.
A performance measurement mode is available as well. Once selected the gauge will
measure 0-60 mph time, 1/8 and 1/4 mile elapsed time with speed.
An integrated shift light, using high intensity LED's, can be programmed to light at any
desirable rpm point. Due to the gauges extremely fast update rate, this light is very
accurate and easy to set. Once you try it you'll find you can't live without it!
Finally the two analog inputs can be configured through menu choices. A linear conversion
can be entered so that an analog signal connected to the gauge can be read in appropriate
units. These inputs are handy for pressure signals such as those from MAP and oil
pressure sensors, analog outputs from Air/Fuel ratio kits, etc. These signal can then be
read and recorded along side the other parameters obtained on the vehicle's bus.
Installation is accomplished by simply plugging the supplied connector into the OBD2 port
below the steering wheel and connecting a separate included wire to a switched 12v
vehicle power source. Virtually plug-and-play! Dual Interceptor Option: Two Interceptors can be purchased with a special splitter
cable that allows both gauges to operate simultaneously. A triple gauge set can be
purchased through special order. |
